gbfisedeesfritpt

EM-363C DC-MOTOR CONTROLLER 12-24V 15A with MODBUS

76,00 € /unit

EM-363A is a full bridge DC-motor starter. It's designed to work with a DC-motor in applications where some special functions are needed. Starter has adjustable acceleration and deceleration ramps, which enable the smooth starts and stops. Adjustable current limit protects the motor against overcurrent and it can also be used as an end-stop. This device also has two settable speeds, which are useful in positioning applications. Control inputs FW and BW start the forward and backward run. STOP is for the motor shut-down but there are also individual limit inputs available for FW and BW directions. SPEED-2 input activates preset speed-2, but it can also be used as an input for analog speed control signal 0-5V. STOP input can be set to work as current limit setting. FAULT terminal has both input and output functions. The pin is normally up, but is pulled down in overheat and conditionally in current trip situation. If FAULT-line is pulled down externally, it will cause a stop and prevent a new start. For example, it's possible to link fault pins of several units
together and achieve a synchronous stop. The device also has parameters for pwm frequency select and freewheel, which is used to release the shaft of the motor. Notice that 16kHz pwm frequency is more silent, but the output current is smaller! Device version A has added Rs-485 Modbus RTU for monitoring and controlling device.
There are two selectable control modes, continuous and impulse. In continuous mode the motor runs as long as the control is active. In impulse mode a short command starts the motor and only a new impulse will change the status. There are also a few special settings, start-kick and auto reverse. The device has selectable input logics. Inputs are divided in two groups, control and limit -inputs. Groups can be individually set for NPN or PNP logic.

The device has black metal housing and lockable spring gage connectors. These connectors are designed for industry and automotive use. Device can be installed laterally or vertically with screw fastening or optionally with DIN-rail fastener. For parameter settings there are the following options: EM-236 interface unit, EM-268 with EmenTool-Lite PC-program and EM-326 with EmenTool-App application for smartphone.


EM-363CTECHNICAL DATA ( PCb v1, prog ver. 363C v1.9 )

Supply voltage cont. max. 10-35V
Overvoltage limit adjustable 15-40V
Start up voltage 9V, shutdown voltage 8V
Continuous current output when ambient temp is <50°C )
15A at 100% speed / 10A at 5-99% speed pwm=2kHz
10A at 100% speed / 5A at 5-99% speed pwm=16kHz
Peak ( 5s.) 30A at 2khz pwm and 25A at 16kHz pwm
Current limit adjustable 0.1-25A ( at start max 30A )
Overheat limit 100°C
Start and stop ramp adjustable 0-5s
PWM frequency 2kHz / 16kHz
Speed input scale ( speed-2 ) 0-5 / 0-10V ( 0-100% )
I-limit input scale ( stop input ) 0-5V = 0-20A
Input control logic: high =4-30V, low=0-1V
Bus Rs-485 Modbus RTU 9600/19200 bps
Control input impedances typ. 47kohm
Limit FW / BW input imped. typ 10kohm
Control input response time typ 5ms.
Fault out. NPN / PNP open coll. max 35V / 1A
Brake out NPN open coll. max. 35V / 4A
Disable in actives Uin < 1V ( NPN )
Motor and supply connectors 2.5mm
Control connectors 1mm
Dimensions 89x26xh81mm ( h88mm with rail foot EM-T55)
Weight 169g
CE-tested for industrial environment ( emc )
Operating temp ( Ta ) -40...60°C

Product files

Stock

  • 139 pcs. in stock

Price

  • 76,00 € /unit