EM-366-SBL BRUSHLESS DC-MOTOR DRIVER 12-48V 30/25A POSITIONING and MODBUS
EM-366-SBL is brushless DC-motor driver with hall sensor feedback. The unit has a mosfet power stage with good efficiency and it meets also todays EMC requirements. The driver can be used with 120° commutation. This driver has true 4Q power stage, and it makes possible to use regenerative braking . In this braking method the supply voltage rises, this voltage rising can be controlled with braking resistor. If uses battery supply then the braking energy can be leaded back to battery and braking resistor will not needed.
The unit has the basic digital command inputs like reset/homing, disable, local/bus and safety stop. There is analog input for position set . EM-366-SBL has PNP output for fault indication use. Some input and output ports and functions can be set and change with parameters. Alternatively this driver can be also controlled via Rs-485 control bus with Modbus protocol.
Driver includes overvoltage, undervoltage and overtemperature protections. These fault situations are indicated with fault on-board LED. Current limit situations can be reset with reset input, reset-timer or by setting analog speed control to value to 0.
This version of EM-366 uses motor feedback pulses also for positioning, little like in servo system. The positioning resolution depends on the numbers of motor poles. for example 1-pole-pari motor 6-positon in round and 7-pole-pair motor 42 position in round.and this round means motor shaft rounds, so with gearbox the resolution can be improved. Driver has own positioning amplifier and with this can be easily adjusted dynamic and accuracy of system. Driver has also RS-485 bus with Modbus control protcol, this make flexible use and control many driver in system.
Setting can be done digitally with EM-236 interface unit or with Emen-Tool lite program installed in PC and EM-328 adapter cable. Parameters stored into nonvolatile memory of device. This interface unit can also be monitored the current and rpm of motor. Parameter setting and monitoring can be also done via Rs-485 bus.
Device can be installed in DIN-rail base and some enclosure options are also available.
Supply voltage 12-48Vdc ( 11-58Vdc )
Overvoltage shutdown 60V
Undervoltage shutdown 10V
Idle current typ. 30mA
Max current 30A cont. ( @ 24Vdc, Tamb. 40 °C )
Max. current 25A cont. ( @ 48Vdc, Tamb. 40 °C )
Max current peak 60A ( max 2s )
Max brake output current 10A
Pwm frequency typ. 16kHz
Overtemperature Temp shut down 90°C
Fan activation temp 55°C
Current limit setting 1-60A ( step 1A )
Current limit analog scale 0-5V = 0-60A
Logic level of digital inputs
"off" = 0-1V or open / "on"= 4-30V
Input impedance of logic inputs 10k
Response time of digital input 2ms
Analog input range 0-5V up to 0-10V
Analog input resolution 10bit. ( 1024 step )
Position counter resolution 31b ( 2147 milj. steps )
Input impedance of analog inputs 100k
Input filter of analog input 100Hz
Hall input max freq. 800Hz
Fault outputs NPN max 50mA
Fan output NPN max. 100mA
EMC measured for industrial and env.
PCB material flammability class UL94V-0
- EN_em-366-SBL.pdf - Download product file (1552 kb)
- EN_em-352_367SBL_Modbus_Data_Address_rev2.pdf - Download product file (138 kb)
- EM-366_3D.zip - Download product file (3808 kb)
- Test_Modbus_connection_with_Qmodbus.pdf - Download product file (209 kb)
- Please send an enquiry.
104,00 € /unit