Harjattomat DC-moottorinohjaimet
Tiedostot
Nimikkeet tässä ryhmässä
EM-106A OHJAIN HARJATTOMILLE DC-MOOTTOREILLE 12-24V 7A
- Kolmivaihelähtö
- Suunnanvaihto
- Hall-anturi syöttö ja tulot
- Sopii 60 tai 120° kommukoinnille
- Aseteltava virtaraja
- Suora-ajo tai takaisinkytketty ajo
- Oma sulake
- Sopii kiskoasennuspohjaan
- Yhteensopiva EM-106:n kanssa
- Paranneltu virtarajan toiminta
EM-151B HARJATTOMAN DC MOOTTORIN OHJAIN 12-24V 25A
- Kolmivaihelähtö
- Normaali tai takaisinkytketty toiminta
- Kontrolloitu suunnanvaihto
- Erilaisia jarrutustapoja
- 60° or 120° kommutointi
- Mahdollisuus ±10V ohjaukseen
- Vika lähtö
- Hyvä hyötysuhde
- Lämpösuoja
- Asennettavissa kiskoasennuspohjaan
EM-206 OHJAIN HARJATTOMILLE DC-MOOTTOREILLE 12-36V 10A
- kolmivaihelähtö
- portaaton nopeudensäätö
- suunnanvaihto
- jarrutus
- optiona ±10V ohjaus
- hall-anturi syöttö ja tulot
- sopii 60 tai 120° kommutoinnille
- aseteltava / ohjattava virtaraja
- vikalähtö
- avoin tai suljettu silmukka -toiminta
- hyvä hyötysuhde
- sopii kiskoasennuspohjaan
EM-206-48 OHJAIN HARJATTOMILLE DC-MOOTTOREILLE 20-56V 5A
- kolmivaihelähtö
- portaaton nopeudensäätö
- suunnanvaihto
- jarrutus
- optiona ±10V ohjaus
- hall-anturi syöttö ja tulot
- sopii 60 tai 120° kommutoinnille
- aseteltava / ohjattava virtaraja
- vikalähtö
- avoin tai suljettu silmukka -toiminta
- hyvä hyötysuhde
- sopii kiskoasennuspohjaan
EM-269A BRUSHLESS DC-MOTOR DRIVER 12-35V 2A
- Only for motors with hall sensor
- Three phase output
- Speed adjustment
- Current limit and trip.
- Open/closed loop modes
- Settable Indication output
- Good efficiency
- Low EMC emissions
- DIN-rail mountable
EM-291A BRUSHLESS DC-MOTOR DRIVER 12-35V 4A
- Only for motors with hall sensors
- Three phase output
- Speed adjustment
- Current limit and trip
- Open/closed loop modes
- Settable indication output
- Good efficiency
- Low current version available ( -LC )
- Low EMC emissions
- DIN-rail mountable
EM-316A Harjaton moottoriohjain 12-35V 10A
- ONLY to the motors with hall sensors
- Three phase output
- Speed and torgue adjustment
- Open/closed loop modes
- Dynamic braking
- Current limit and trip
- Fault and overcurrent outputs
- 60° / 120° commutation options
- Good efficiency
- Low EMC emissions
- DIN-rail mountable
- EM-316A is compatible with EM-316
- Added EM-A1 card slot for ±10V control
- Rpm-pulse output option ( prog v1.5 )
EM-346 Harjaton moottoriohjain 12-35V 10A
- ONLY to the motors with hall sensors
- Three phase output
- Speed and torque adjustment
- Open/closed loop modes
- Regenerative braking option
- True 4Q-power stage
- Braking resistor output
- Current limit and trip
- Symmetrical control option ±5V or ±10V
- Fault and overcurrent outputs
- Good efficiency
- Low EMC emissions
- DIN-rail mountable
- Rpm-pulse output option
- New in firmware version v1.4
- + improved closed loop features ( param. 1)
- + new operating mode options ( param. 11)
- + one option added disable input ( param. 14 )
- + control for magnetic brake ( param. 18 )
EM-346-48V BRUSHLESS DC-MOTOR DRIVER 24-48V 10A
- ONLY to the motors with hall sensors
- Three phase output
- Speed and torque adjustment
- Open/closed loop modes
- Regenerative braking option
- True 4Q-power stage
- Braking resistor output
- Current limit and trip
- Symmetrical control option ±5V or ±10V
- Fault and overcurrent outputs
- Good efficiency
- Low EMC emissions
- DIN-rail mountable
- Rpm-pulse output option
- New in firmware version v1.4
- + improved closed loop features ( param. 1)
- + new operating mode options ( param. 11)
- + one option added disable input ( param. 14 )
- + control for magnetic brake ( param. 18 )
EM-347A BRUSHLESS DC-MOTOR DRIVER 12-36V 55A EM-347A-fan 12-36V 70A
- ONLY to the motors with hall sensors
- Three phase output
- Speed and torgue adjustment
- Open/closed loop modes
- Dynamic braking
- Control output for cooling fan.
- True 4Q-power stage
- Braking resistor output
- Selectable brake mode
- Current limit and trip
- Symmetrical control option ±5V or ±10V
- Fault and overcurrent outputs
- Good efficiency
- Low EMC emissions
- DIN-rail mountable
- Rpm-pulse output option
- A-version has 20% improved output current
- A-version available with integrated fan
- Firmware v1.4 extended control opt. par. 11
- Firmware v1.9 options added to par. 14 and 17
EM-347B BRUSHLESS with MODBUS( BLDC ) MOTOR DRIVER 12-48V 50A
- Only to the motors with HALL sensors
- motors 12V recom. up to 800W
- motors 24V recom. up to 1200W
- motors 48V recom. up to 1600W
- Three phase output
- Speed and torgue adjustment
- Open/closed loop modes
- Dynamic braking
- Control output for cooling fan.
- True 4Q-power stage
- Braking resistor output
- Selectable brake mode
- Current limit and trip
- Symmetrical control option ±5V or ±10V
- Fault and overcurrent outputs
- Good efficiency
- Low EMC emissions
- DIN-rail mountable
- Rpm-pulse output option
- B-board has extended voltage range
- B-board has shutdown input for idle reduction
- B-board replaced earlier A-versions ( all voltage )
- B-board has Rs-485 port ( Modbus RTU )
- B-board support B version firmwares
- B-version HW and SW offer special stop modes
- B-version board v3 support hold current option
- Prog. v1.8 param. 21 added "hold current"
- Prog v1.9 Im zero calib. added, param. 1 =3
- Prog v1.9 magn brake "slow" added to param. 1
EM-352 BRUSHLESS DC-MOTOR DRIVER 12-35V 8A
- Only for motor with Hall sensors
- Speed and torgue adjustment
- Open/closed loop modes
- Regenerative braking option
- Braking resistor output
- Fan control output
- For motors up to 80W@12V 125W@24V
- Current limit and trip
- Indication output option
- Good efficiency
- Low EMC emissions
- DIN-rail mountable
- Firmvare v1.0 or later
- Rs-485 Modbus control option
- Firmware v1.7 or later
- Added input functions, par. 11,13, 20
- Added power on mode, parameter 15
- Firmware v1.8
- par 20 added "inverted disable" option
- closed loop start up improved
EM-352-SBL BRUSHLESS DC-MOTOR DRIVER 12-24V 8A POSITIONING and MODBUS
- Three phase output
- Speed and torgue adjustment
- Rs-485 Modbus cont. option
- Servo amplifier for positioning
- Regenerative braking option
- Position counter 31bit
- True 4Q-power stage
- Braking resistor output
- Output current 8A
- Current limit and trip
- Good efficiency
- Low EMC emissions
- Compact size
- DIN-rail mountable
- Firmware v1.6 added features
- current limitation smoothed
- counter max . freq. increased
- start level added, param. 19
- Fiemware v1.9 added par. 18 pos. 8
EM-356B BRUSHLESS DC-MOTOR DRIVER 12-35V 15A ( 20A )
- Only for motors with Hall sensors
- Speed and torgue adjustment
- Open/closed loop modes
- Regenerative braking option
- Braking resistor output
- Fan control output
- For motors up to 100W @ 12V,
- and 200W@ 24V
- Current limit and trip
- Indication output option
- Good efficiency
- Low EMC emissions
- DIN-rail mountable
- Firmvare v1.0 or later
- Rs-485 Modbus control option
- Firmware v1.7 or later
- Added input functions, par. 11,13, 20
- Added power on mode, parameter 15
- Firmvare v1.8
- par 20 added "inverted disable" option
- closed loop start up improved
EM-356B-SBL BRUSHLESS DC-MOTOR DRIVER 12-24V 15/20A POSITIONING and MODBUS
- ONLY to the motors with hall sensors
- Three phase output
- Speed and torgue adjustment
- Rs-485 Modbus cont. option
- Servo amplifier for positioning
- Regenerative braking option
- Position counter 31bit
- True 4Q-power stage
- Braking resistor output
- Fan control output
- Output current 25A with fan
- Current limit and trip
- Good efficiency
- Low EMC emissions
- DIN-rail mountable
- EM-356B-SBL replaces earlier EM-356A-SBL
- EM-356B works -B version or later firmwares
- v1.8 improved position counter freq.
- v1.8 improved currrent limit features
- v1.8 added param. 19 "start level"
EM-356C BRUSHLESS DC-MOTOR DRIVER 12-48V 15A ( 20A )
- Only for with Hall sensors
- Three phase output
- Speed and torgue adjustment
- Open/closed loop modes
- Regenerative braking option
- Braking resistor output
- Fan control output
- For motors up to 300W
- Current limit and trip
- Indication output option
- Good efficiency
- Low EMC emissions
- DIN-rail mountable
- Firmvare v1.0 or later
- Rs-485 Modbus control option
- Firmware v1.7 or later
- Added input functions, par. 11,13, 20
- Added power on mode, par 15
- Firmware v1.8
- added inverted disable. to par 20
- closed loop start up improved.
- Haedware EM-356 -C series
- extended supply range, up to 48V
EM-366 BRUSHLESS DC-MOTOR DRIVER 12-48V 30/25A
- Only for motors with Hall sensors
- Speed and torgue adjustment
- Open/closed loop modes
- Regenerative braking option
- Braking resistor output
- Fan control output
- For motors up to 200W @12V
- 300W @ 24V and 400W @ 48V
- Current limit and trip
- Indication output option
- Good efficiency
- Low EMC emissions
- DIN-rail mountable
- Firmvare v1.0 or later
- Rs-485 Modbus control option
- Firmware v1.7 or later
- Added input functions, par. 11,13, 20
- Added power on mode, parameter 15
- Firmware v1.8
- par 20 added "inverted disable" option
- closed loop start up improved
EM-366-SBL BRUSHLESS DC-MOTOR DRIVER 12-48V 30/25A POSITIONING and MODBUS
- ONLY to the motors with hall sensors
- Three phase output
- Speed and torgue adjustment
- Rs-485 Modbus cont. option
- Servo amplifier for positioning
- Regenerative braking option
- Position counter 31bit
- True 4Q-power stage
- Braking resistor output
- Fan control output
- Output current up to 30A
- Current limit and trip
- Good efficiency
- Low EMC emissions
- DIN-rail mountable