DC-moottorinohjain >10A
Tiedostot
Nimikkeet tässä ryhmässä
DC-MOTOR CONTROLLER EM-362 12-24V 160A
- high current output
- brake load output
- recommeded motor up to
- 1.8 kW at 12V and 2.7 kW at 24V
- current limit
- current limit for brake also
- zero-current limit
- speed setting/adjustment
- flexible control inputs
- impulse / continuous mode
- rail base mountable
- digital parameter setting
- 2/16kHz pwm freq. options
- APPLICATIONS
- vehicles
- winches
- steering prop
EM-115 DC-MOOTTORISÄÄDIN 12-36V 25A 4-QUAD.
- Pieni koko
- Neljä ohjausquadranttia
- Hyvä hyötyaste >92%
- Moottoreille 50-500W
- Sopii kiskoasennuspohjaan
- Säädettävä virtaraja
- Säädettävä ramppi
EM-115-48 DC-MOOTTORISÄÄDIN 20-60V 25A 4-QUAD.
- Pieni koko
- Neljä ohjausquadranttia
- Hyvä hyötyaste >92%
- Moottoreille 50-500W
- Sopii kiskoasennuspohjaan
- Säädettävä virtaraja
- Säädettävä ramppi
EM-231B CONTROL UNIT FOR DOORS AND HATCHES
- Motor output 24Vdc 3A peak 6A
- 2-pulse line position feedback
- Safety switch input with monitoring
- Proximity switch input ( door radar )
- RF remote controlled option ( -RC )
- 2 or 4 button keyfob options
- Robust enclosure
- Digitally settable parameters
- Inbuilt 230Vac power supply
- New version B replacing EM-231A
- Not compatible with earlier EM-231
- ACCESSORIES - which you may need
- Parameter setting device
- EM-328 series or EM-236A
- RF-keyfob transmitters for -RC version
- EM-A14T-FM or EM-A14T-FM-4
EM-231B-RC CONTROL UNIT FOR DOORS AND HATCHES
- Motor output 24Vdc 3A peak 6A
- 2-pulse line position feedback
- Safety switch input with monitoring
- Proximity switch input ( door radar )
- RF remote controlled option ( -RC )
- 2 or 4 button keyfob options
- Robust enclosure
- Digitally settable parameters
- Inbuilt 230Vac power supply
- New version B replacing EM-231A
- Not compatible with earlier EM-231
- ACCESSORIES - which you may need
- Parameter setting device
- EM-328 series or EM-236A
- RF-keyfob transmitters for -RC version
- EM-A14T-FM or EM-A14T-FM-4
EM-239 Rinnakkaisohjain kahdelle toimilaitteelle 12/24Vdc 2x10A or 2x20Apeak
- synchronized parallel driving
- operates with pulse feedback
- input for negative or positive pulses
- current and temperature limit
- settable drive speed
- acceleration and deceleration ramps
- different control modes
- wide range of parameters
- easy setting with serial interface
- good repeatability of settings
- autobalance feature
- one or double pulse mode
- safety reverse function ( prog. v2.4 or later)
EM-241-SAF PAIKOITUSOHJAIN 12-24V 15A
- analog feedback
- 5V, 10V or 4-20mA control
- position accuracy max. 0,1%
- solid state power stage
- small size, great performance
- digitally settable parameters
- verstile dynamic settings
- housing options available
- EMC tested
- Versions additions
- Pwm freq, 2/16kHz ( since prog. v1.3 )
- Improved accurate , parameter 17, prog. ( v1.5 )
- Added Modbus parameters 26, 27 and 28 ( v1.8 )
EM-241B-PLI DC-MOTOR CONTROLLER 12-24V 15A
- 2ch pulse counter inputs
- pulse counter end limits.
- for motor with 2 pulse output
- current limit
- zero current limit
- overvoltage brake
- recommended max. motor size
- 120W@12V and 200W@24V
- speed setting
- PWM 2 or 16 kHz
- flexible control inputs
- impulse / continuous mode
- rail base mountable
- digital parameter setting
- dip switch only in pcb. version B and C
- firmware work on pcb. version B and C
- firmware v2.1 pulse inputs max. speed improved
- APPLICATIONS
- hatch and gate opener
- actuator stroke, force and speed adjust
EM-241C DC-MOTOR CONTROLLER 12-24V 15A
- small size
- high current output
- current limit
- zero current limit
- overvoltage brake
- speed setting
- flexible control inputs
- impulse / continuous mode
- rail base mountable
- digital parameter setting
- C-version replaces A and B versions
- C-firmware can be loadad B ver. card
- C.version available with molex connector
- current limit setting input ( new )
- freewheel options ( new )
- 2 or 16kHz PWM freq. ( new )
- input range adjust ( new from prog. v1.5 )
- bus option / pause input ( new from v1.7 )
EM-241C-48V DC-MOOTTORIN OHJAIN 24-48V 10A
- small size
- high current output
- current limit
- zero current limit
- overvoltage brake
- speed setting
- flexible control inputs
- impulse / continuous mode
- rail base mountable
- digital parameter setting
- 48V version of EM-241C
- current limit setting input ( new )
- freewheel options ( new )
- 2 or 16kHz PWM freq. ( new )
EM-241C-JS1 DC-MOTOR CONTROLLER 12-24V 15A
- JS1 is specially for joystick use
- three point calibration
- small size
- high current output
- current limit
- overvoltage brake
- 2 or 16kHz pwm frequency
- motors up to 200W
- own speed ranges for FW and REV.
- rail base mountable
- digital parameter setting
- JS1 program can be update
- also for standard EM-241 board
- Prog. 1.3 direction change input added
- Prog. 1.4 stop input options added
- Prog. 1.6 joystick wire breakage detection
EM-243-PLI DC-MOTOR CONTROLLER 12-48V 50A
- 2ch pulse counter inputs
- pulse counter limits.
- for motor with pulse output
- overcurrent ( torque ) limit
- overvoltage brake
- recommended motor size max.
- 350W @ 12V
- 500W @ 24V
- 600W @ 48V
- speed setting
- PWM 2 or 16 kHz
- flexible control inputs
- brake output
- impulse / continuous mode
- rail base mountable
- prog. v2.0 two option added to param. 10
- prog. v2.1 pulse input freq. max. improved
- prog. v2.2 added learn routine to par. 23
- APPLICATIONS
- hatch opener
- actuator stroke and speed adjust
EM-243-SPF POSITIONING DRIVER 12-24V 50A
- quadrature pulse counting
- multiple dynamic settings
- solid state power stage
- one or two pulse feedback
- voltage or mA control
- position accuracy max. 0.2%
- versatile setting options
- brake output
- digitally settable parameters
- housing options available
- motors up to 500W
- EMC measured product
EM-243C DC-MOTOR CONTROLLER 12-48V 50A
- For Motor up to 500W
- small size
- high current output
- current limit
- zero current limit
- speed setting
- flexible control inputs
- impulse / continuous mode
- rail base mountable
- digital parameter setting
- C ver. card compatible with A version card
- C firmware can be loaded A-ver. card
- C ver. new features
- + freewheel options parameter (param 19)
- + 2 or 16kHz pwm freq.select (param. 20)
- + current limit analog input ( param 6&7 )
- + speed+dir operating mode (param. 5)
- + Fan and Brake available in board 243C v.2
- + Extend operating voltage in board 243C v.2
- + prog. -C v1.5 speed input range adjust
- + prog -C v1.7 bus option / pause input
EM-243C-JS1 DC-MOTOR CONTROLLER 12-48V 50A
- JS1 is specially for joystick use
- three point calibration
- compact size
- for motor up to 500W
- high current output
- current limit
- overvoltage brake
- own speed ranges for FW and REV.
- rail base mountable
- digital parameter setting
- JS1 program can be update
- also for standard EM-243A or 243C boards
- Board version C has extended
- operating voltage 42V -> 48V
- Prog. 1.3 direction change input added
- Prog. 1.4 stop input, brake output and
- fan output ottions added
- Prog 1.6 wire breakage detection added
EM-247C DC-MOTOR STARTER and CONTROLLER 12-36V 70A
- recommended motor max.
- 12V 0.7kW and 24V 1kW
- current ( torque ) limit
- starter or speed control mode
- flexible control inputs
- brake res. output
- impulse / continuous mode
- rail base mountable
- digital parameter setting
- APPLICATION
- DC motor soft start
- DC motor speed control
- DC motor direction change
- small vehicles
- lifters and conveyor
- actuators torque limit
EM-282D DC-MOTOR CONTROLLER 12-48V , 100A - 80A
- for motors up to 1.5kW
- available with integrated fan.
- high current output
- brake load output
- current limit
- current limit for brake also
- zero-current limit
- speed setting/adjustment
- flexible control inputs
- impulse / continuous mode
- rail base mountable
- digital parameter setting
- C versions program
- + 2/16kHz pwm freq. options
- + freewheel options
- + autoreverse option
- + running indication options
- + expanded input logic options
- + thermal cont. Fan-output
- + speed range adj. v1.5 ->
- + serial com. control option v1.8 ->
- D board ver. replaces earlier versions
- both EM-282C and EM-282C-48V
- + extended supply voltage range
- + added Rs-485 bus
- + D pcb v3 shutdown input added
EM-282D-fan DC-MOTOR CONTROLLER 12-48V , 100A - 80A
- for motors up to 1.5kW
- available with integrated fan.
- high current output
- brake load output
- current limit
- current limit for brake also
- zero-current limit
- speed setting/adjustment
- flexible control inputs
- impulse / continuous mode
- rail base mountable
- digital parameter setting
- C versions program
- + 2/16kHz pwm freq. options
- + freewheel options
- + autoreverse option
- + running indication options
- + expanded input logic options
- + thermal cont. Fan-output
- + speed range adj. v1.5 ->
- + serial com. control option v1.8 ->
- D board ver. replaces earlier versions
- both EM-282C and EM-282C-48V
- + extended supply voltage range
- + added Rs-485 bus
- + D pcb v3 shutdown input added
EM-282D-JS1 DC-MOTOR CONTROLLER 12-48V 100A
- JS1 is specially for joystick use
- three point calibration
- small size
- high current output
- current limit
- for motors up to 1.5kW
- overvoltage brake
- own speed ranges for FW and REV.
- rail base mountable
- digital parameter setting
- JS1 program can be update
- also for standard EM-282 board
- Prog. 1.3 direction change input added
- Prog. 1.4 stop input, brake output and
- fan output ottions added
- Prog 1.6 wire breakage detection added
- prog v1.7 ( for D-board only ) Rs-485 added
- D-board series has extended supply range
EM-285 DC-MOOTTORIN NOPEUDENSÄÄDIN 12 / 24V 20A
- 1-suuntainen nopeussäätö
- Paneeliasennettava
- Pieni koko
- Moottorisuositus 30-200W
- Hyvä nopeustarkkuus
- Kuorman kompensointi RxI
- Säädettävä virtaraja
- Ylilämpösuojaus
- EMC testattu ( CE merkattu )
EM-295C DC Moottoriohjain 30A
- DC motor speed controller, one direction
- Recom, motors up to 200W@12V, 300W@24V and 400W@48V
- Regenerative braking
- Braking resistor or Magnetic brake control output
- Voltage stabilized and RxI load compensation
EM-337A-48V PLI PARALLEL DRIVER FOR 4 ACTUATORS or MOTORS 24-48Vdc 4x8A / 4x15A peak
- FEATURES
- synchronized 4 parallel driving
- operates with pulse feedback
- pulse counting PNP or NPN logic
- quadrature pulse counting
- current and temperature limit
- settable drive speed
- 2 or 16kHz pwm frequency
- acceleration and deceleration ramps
- stroke length limitation
- setting with serial interface
- brake ( release ) output
- safety switch input
- Rs-485 ( Modbus ) control
- safety reverse function
- A-version replaces earlier versions but
- A-version works only with A-ver. firmware
- APPLICATIONS
- table lifter
- hatch control
- worktop control
EM-337A-48V-SPF POSITIONING DRIVER for 4 PARALLEL DC-motor 24/48Vdc 4x8A / peak 4x15A , Rs-485
- positioning with 0-5V or 0-10V signal
- positioning also with Rs-485 Modbus
- synchronized 4 parallel driving
- operates with pulse feedback
- pulse counting PNP or NPN logic
- quadrature pulse counting
- current and temperature limit
- settable drive speed
- 2 or 16kHz pwm frequency
- acceleration and deceleration ramps
- stroke length limitation
- setting with serial interface
- brake ( release ) output
- safety switch input
- Rs-485 ( Modbus ) control
- safety reverse function
- The A version replaced earlier versions
- but A-version works only A-ver- firmware !
- APPLICATIONS
- table lifter
- hatch control
- worktop control
EM-337A-PLI PARALLEL DRIVER FOR 4 ACTUATORS or MOTORS 12/24Vdc 4x10A
- FEATURES
- synchronized 4 parallel driving
- operates with pulse feedback
- pulse counting PNP or NPN logic
- quadrature pulse counting
- current and temperature limit
- settable drive speed
- 2 or 16kHz pwm frequency
- acceleration and deceleration ramps
- stroke length limitation
- setting with serial interface
- brake ( release ) output
- safety switch input
- Rs-485 ( Modbus ) control
- safety reverse function
- A-version replaces earlier versions but
- A-version works only with A-ver. firmware
- APPLICATIONS
- table lifter
- hatch control
- worktop control
EM-337A-SPF POSITIONING DRIVER for 4 PARALLEL DC-motor 12/24Vdc 4x10A / peak 4x20A , Rs-485
- positioning with 0-5V or 0-10V signal
- positioning also with Rs-485 Modbus
- synchronized 4 parallel driving
- operates with pulse feedback
- pulse counting PNP or NPN logic
- quadrature pulse counting
- current and temperature limit
- settable drive speed
- 2 or 16kHz pwm frequency
- acceleration and deceleration ramps
- stroke length limitation
- setting with serial interface
- brake ( release ) output
- safety switch input
- Rs-485 ( Modbus ) control
- safety reverse function
- The A version replaced earlier versions
- but A-version works only A-ver- firmware !
- APPLICATIONS
- table lifter
- hatch control
- worktop control
EM-339A-48V-PLI PARALLEL DRIVER FOR TWO ACTUATORS or MOTORS 24V-48dc 2x8A or 2x15Apeak, Rs -485
- synchronized parallel driving
- operates with pulse feedback
- pulse counting PNP or NPN logic
- quadrature pulse counting
- current and temperature limit
- 2 or 16kHz pwm frequency
- acceleration and deceleration ramps
- stroke length limitation
- setting with serial interface
- brake ( release ) output
- safety switch input
- safety reverse function
- EM-339A is recommended as a substitute
- for EM-239 in new application
- EM-339A version has added Rs-485 bus
- version -A board needa A version firmvare
- APPLICATIONS
- For Table lifter and Door and Hatch control
- Synchronous Actuator or Pilar control
EM-339A-48V-SPF POSITIONING DRIVER FOR TWO PARALLEL DC-MOTOR 24/48Vdc 2x8A or 2x15Apeak, Rs-485
- synchronized parallel driving
- operates with pulse feedback
- input for negative or positive pulses
- current and temperature limit
- settable drive speed
- speed regulation
- 2 or 16kHz pwm frequency
- acceleration and deceleration ramps
- analog input for position control
- parameters for stroke length adjust
- easy setting with serial interface
- brake ( release ) output
- quadrature pulse counting
- emerg. switch input
- safety reverse function
- low emissions, EMC tested
- Modbus control port
- EM-339A is recommended as a substitute
- for EM-239 in new application
- EM-339A version pcb has added Rs-485
EM-339A-PLI PARALLEL DRIVER FOR TWO ACTUATORS or MOTORS 12/24Vdc 2x10A or 2x20Apeak, Rs -485
- synchronized parallel driving
- operates with pulse feedback
- pulse counting PNP or NPN logic
- quadrature pulse counting
- current and temperature limit
- 2 or 16kHz pwm frequency
- acceleration and deceleration ramps
- stroke length limitation
- setting with serial interface
- brake ( release ) output
- safety switch input
- safety reverse function
- EM-339A is recommended as a substitute
- for EM-239 in new application
- EM-339A version has added Rs-485 bus
- version -A board needa A version firmvare
- APPLICATIONS
- For Table lifter and Door and Hatch control
- Synchronous Actuator or Pilar control
EM-339A-SPF POSITIONING DRIVER FOR TWO PARALLEL DC-MOTOR 12/24Vdc 2x10A or 2x20Apeak, Rs-485
- synchronized parallel driving
- operates with pulse feedback
- input for negative or positive pulses
- current and temperature limit
- settable drive speed
- speed regulation
- 2 or 16kHz pwm frequency
- acceleration and deceleration ramps
- analog input for position control
- parameters for stroke length adjust
- easy setting with serial interface
- brake ( release ) output
- quadrature pulse counting
- emerg. switch input
- safety reverse function
- low emissions, EMC tested
- Modbus control port
- EM-339A is recommended as a substitute
- for EM-239 in new application
- EM-339A version pcb has added Rs-485
EM-341C DC-MOTOR CONTROLLER 12-24V 15A
- small size
- high current output
- current limit
- zero current limit
- overvoltage brake
- speed setting
- flexible control inputs
- impulse / continuous mode
- rail base mountable
- digital parameter setting
- current limit setting input
- freewheel options
- 2 or 16kHz PWM freq.
- Magnetic brake control output
- Molex connector option
EM-348-48V-PLI DC-MOTOR CONTROLLER 24-48V, 10A, Rs-485, Modbus
- Integrated Rs-485 bus
- Modbus RTU
- Parameter setting with Bus
- Control and monitor with Bus
- High current output
- Current limit
- 2ch pulse counter inputs
- pulse counter limits.
- Zero current trip
- Overvoltage brake
- Speed setting
- Magnetic brake control output
- Flexible control inputs
- Rail base mountable
- Low EMC emissions
- Firmware v2.0, param. 10 extended
EM-348-48V-SPF DC-MOTOR CONTROLLER with MODBUS 24-48V 10A
- Integrated Rs-485 half dublex Bus
- Modbus RTU
- Parameter setting with Bus
- Control with Bus
- Monitoring with Bus
- High current output
- Current limit
- Position accuracy 0.2%
- Zero current trip
- Overvoltage brake
- Speed setting
- Various firmware version
- Magnetic brake control output
- Flexible control inputs
- rail base mountable
EM-348-PLI DC-MOTOR CONTROLLER 12-24V, 15A, Rs-485, Modbus
- Integrated Rs-485 bus
- Modbus RTU
- Parameter setting with Bus
- Control and monitor with Bus
- High current output
- Current limit
- 2ch pulse counter inputs
- pulse counter limits.
- Zero current trip
- Overvoltage brake
- Speed setting
- Magnetic brake control output
- Flexible control inputs
- Rail base mountable
- Low EMC emissions
- Firmware v2.0, param. 10 extended
EM-348-SAF DC-MOTOR CONTROLLER with MODBUS 12-24V 15A
- Analog position feedback input.
- Integrated Rs-485 half dublex Bus
- Modbus RTU
- Parameter setting with Bus
- Control and monitoring with Bus
- High current output
- Current limit
- Position accuracy 0.2%
- Zero current trip
- Overvoltage brake
- Speed setting
- Various firmware version
- Also available low current 6A ver.
- Magnetic brake control output
- Flexible control inputs
- rail base mountable
EM-348-SPF DC-MOTOR CONTROLLER with MODBUS 12-24V 15A
- Positioning with pulse feedback
- Integrated servo amplifier.
- Position accuracy 0.2%
- Inbuilt Rs-485 half dublex Bus
- Modbus RTU
- Parameter setting with Bus
- Monitoring with Bus
- High current output
- Current limit
- Overvoltage brake
- Also available low current 6A ver.
- Magnetic brake control output
- Flexible control inputs
- rail base mountable
EM-348C DC-MOTOR CONTROLLER with MODBUS 12-24V, 15A and Rs-485 BUS
- Integrated Rs-485 bus
- Modbus RTU
- Parameter setting with Bus
- Control and monitor with Bus
- High current output
- Current limit
- Zero current trip
- Overvoltage brake
- Speed setting
- Magnetic brake control output
- Flexible control inputs
- Rail base mountable
- Low EMC emissions
EM-348C-48V DC-MOTOR CONTROLLER with MODBUS 24-48V, 10A and Rs-485 BUS
- Integrated Rs-485 bus
- Modbus RTU
- Parameter setting with Bus
- Control and monitor with Bus
- High current output
- Current limit
- Zero current trip
- Overvoltage brake
- Speed setting
- Magnetic brake control output
- Flexible control inputs
- Rail base mountable
- Low EMC emissions
DC-MOTOR CONTROLLER EM-362D 12-36V, 160A
- for motors up to 1.8kw@12V,
- 2.5kW@24V and 3kW at 36V
- integrated fan.
- high current output
- brake load output
- current limit
- current limit for brake also
- zero-current limit
- speed setting/adjustment
- flexible control inputs
- impulse / continuous mode
- rail base mountable
- digital parameter setting
- D board ver. replaces earlier version EM-362
- + extended supply voltage range 12-36Vdc
- + added Rs-485 bus
- + D pcb v3 shutdown input added
- APPLICATIONS
- vehicles
- winches
- steering prop
EM-363C DC-MOTOR CONTROLLER 12-24V 15A with MODBUS
- High current output
- Current limit
- Overvoltage brake
- Speed setting
- Flexible control inputs
- Impulse / continuous mode
- Rail base mountable
- Digital parameter setting
- Current limit setting input
- Freewheel options
- 2 or 16kHz PWM frequency
- Magnetic brake control output
- Lockable, spring gage connectors
- - C version Rs-485 Modbus added
- Different firmware option available
EM-368C DC-MOTOR CONTROLLER with MODBUS 12-48V, 35A and Rs-485 BUS
- Integrated Rs-485 bus
- Modbus RTU
- Parameter setting with Bus
- Control and monitor with Bus
- High current output
- Current limit
- Zero current trip
- Overvoltage brake
- Speed setting
- Magnetic brake control output
- Flexible control inputs
- Rail base mountable
- Low EMC emissions
EM-A24-SAF DC-moottori ohjain
- analog feedback
- multiple dynamic settings
- solid state power stage
- one or two pulse feedback
- voltage or mA control
- position accuracy max. 0.2%
- versatile setting options
- digitally settable parameters
- housing options available
- 2/16kHz pwm frequncy options
- CE marked product
EM-A24C-JS1 DC Motor Driver Module
- EM-A24 is a DC-motor driver module.
- It's based on EM-241 driver card.
- This module is PCB mountable.
- This module has effective H-bridge power stage.