EM-324-SPF Positioning Driver

EM-324-SPF is a positioning driver to be used with DC-motors. The solid state power stage operates with high efficiency and as its realized with FET-transistors. Its literally everlasting compared to relay solutions. Feedback is done with one or two line pulse signal. Although position feedback can be done with one pulse line it is always preferred and more secure to do it with two 0°/90° pulse lines. This driver includes an analog control with three signal ranges, 0-5,5V, 0-11V or 4-20mA. Input is freely scalable inside the range. The max. electrical accuracy of the driver and feedback is 0.2% which is adequate for most actuator positioning applications.
The settings and adjustments are done with parameters as in all new generation Electromen products. Included in the parameters is also the learn routine which will help to determine the full movement range fast and easily. Additively the movement range can be modified from both ends with SW-limit parameters. Possible cumulating pulse count errors can be avoided with manually or automatically triggerable home drive. Current limits and driving speeds can be set individually for both directions. Driver includes also many other dynamic adjustment features like parameter for load compensation, dead-zone setting (positioning window), start and stop ramps for smooth direction change and braking zone for well operating positioning. 

The parameter setting and status monitoring is done with EM-236 Interface Unit. With EM-236 the right parameters can also be copied easily to other driver units. The on-board LED-light indicates the possible fault situations with blinking codes. If needed, the fault alarm can be also given out trough combiport (pin. 13). This port can be set as "position OK." output or it can work as an analog position signal output. Additively it can work also as disable input. Device is EMC tested for industrial and household environment and operating temperature range is quite wide. There are also same housing options available for EM-324-SPF driver card as for the standard EM-324.


TECHNICAL DATA

Supply voltage10-35V
Shutdown voltage8V
Power up voltage9V
Motor current (cont.)4A at 2kHz / 3A at 16kHz
Motor current (momentary)6A
Current limit adjustable0.1-6A (max. 8A at start)
Overtemperature limit100°C
PWM frequency2kHz / 16kHz
Pulse sampling rate0.2ms
Input frequency of pulse lines (max.)800Hz
Control input range (position)0-5.5V / 0-11V / 4-20mA
Positioning potentiometer10kΩ recommended, 22kΩ max.
Input resistor for mA signal250Ω (socket on board)
Position output signal range0-5V or 0.5-4.5V, 0V for FAULT
Digital input levelsHigh = 4-30V, Low = 0-1V
Digital input impedanceTyp. 47kΩ
Limit-FW / -BW and pulse input impedanceTyp. 10kΩ
COMBIPORT pin 13
Fault outputNPN, open collector, max. 30V / 50mA
Disable inputUin < 1V (NPN)
Position output impedance1kΩ
Connectors for motor and supplyMax. 2.5mm² cable
Connectors for signalsMax. 1mm² cable
Operating temperature (Ta)-40...60°C
Dimensions72x42x25mm
Weight80g
CE-tested for household and industrial environment (EMC)EN-55022B, EN-61000-4-3, -4, -5, -6 passed

Tuotetiedostot

EN_em-324-SPF.pdf (205,05 KB)
EN_em-Rail_bases.pdf (2 833,53 KB)
Varastosaldo: 10 kpl
34,00 €
VAT 0%

AAA - credit rating

ISO-certified suppliers and subcontractors

100% Finnish production chain

Device design, programming, and laboratory testing

Short delivery time

Takaisin ylös
Sivustomme käyttää evästeitä käyttäjäkokemuksen parantamiseksi. Voit muuttaa eväste valintojasi asetuksista
1 Tuotetta ostoskorissa
Ostoskori
Yhteensä:
0,00€