EM-348C DC-Motor Controller with Modbus RS485

EM-348C is a full bridge DC-motor starter. It is designed to work with DC-motor in applications where some special functions are needed. Driver has 4-quadrant full-bridge powerstage, and also brake control power output. The powerstage can be selected for use with two different frequency, the one is efficient and the other is silent . The powerstage uses smooth switching technology and has very low EMC emission. Parameter allows powerstage to be set brake or freewheel mode when stand-by.
This device is designed to control with Rs-485 Bus.The control bus use Modbus RTU protocol and with the Bus there can be set, speed, direction, accelaration and deceleration ramps and current limit. Also the monitoring and parameter setting are possible with the Bus. There is a separate instruction for operating the bus.
Device has also some local control inputs FW and BW for start the forward and backward run. STOP is for the motor shut-down but there are also available individual limit inputs for FW and BW directions. FAULT terminal has at the same time input and output function, the pin is normally low, and in fault situation it will pull up for examle if overheat of current trip occurs. If FAULT-line is pulled up externally it will cause a stop and prevent the new start, so it works like Disable input. For example: if system has several units and those
FAULT pins is connected together, then Fault of one card will disable other units also,
Device has two selectable control modes, continuous and impulse. In continuous mode the motor runs as long as the control is active. In impulse mode a short comand starts the motor, and only a new impulse will change the status. There is also few special settings start-kick and auto reverse. The card has selectable input logics. Inputs are divided in two groups, control and limit -inputs. Groups can be individually set for NPN or PNP logic.


TECHNICAL DATA (PCB v1, Prog. EM-348-C v1.9)

Supply voltage (continuous, max.)10-35V
Overvoltage limit (adjustable)15-40V (hardware limitations)
Start-up voltage9V
Shutdown voltage8V
Continuous current output (@ 15°C ambient)15A at 100% speed / 10A at 5-99% speed (PWM = 2kHz)
10A at 100% speed / 5A at 5-99% speed (PWM = 16kHz)
Peak current (5s)30A at 2kHz PWM, 25A at 16kHz PWM
Current limit (adjustable)0.1-25A (Max. 30A at start)
6A version current (typical)~2.5 times smaller than standard
Overheat limit100°C
Start/stop ramp (adjustable)0-5s
PWM frequency2kHz / 16kHz
Input control logicHigh = 4-30V, Low = 0-1V
Control input impedanceTyp. 47kΩ
Limit/pulse input (pin 2 and 3) impedanceTyp. 10kΩ
Control input response timeTyp. 5ms
Fault output (PNP open collector)12-22V / Max. 50mA
Brake output (NPN open collector)Max. 35V / 2A
Min. brake resistor6.8Ω @ 12V / 15Ω @ 24V
Disable input (active)Uin > 4V (PNP)
Bus communicationRS-485, two-wire half-duplex, 9600 kbps
Motor and supply connectors2.5mm²
Control connectors1mm²
Dimensions42 x 72 x 25mm (6A version: 18mm height)
Dimensions (DIN-rail base)45 x 80 x 45mm
CE-tested for industrial environment (EMC)Yes
Operating temperature (Ta)-40...60°C
Weight75g

Product files

EN_em-348C.pdf (1,203.70 KB)
Modbus_common_part_10.2.2021.pdf (393.18 KB)
Modbus_EM-C_Drivers_19.10.2020.pdf (189.83 KB)
EN_em-Rail_bases.pdf (2,833.53 KB)
Stock: 911 pcs.
59,00 €
VAT 0%

AAA - credit rating

ISO-certified suppliers and subcontractors

100% Finnish production chain

Device design, programming, and laboratory testing

Short delivery time

Back to top
Our website uses cookies to enhance user experience. You can adjust your preferences from the settings
1 Items in cart
Cart
Overall:
0,00€