EM-348-PLI DC-Motor Controller with Modbus RS485

EM-348-pli is a full bridge DC-motor starter. It is designed to work with DC-motor in applications where some special functions are needed. Starter has adjustable acceleration and deceleration ramps, which make possible the smooth starts and stops. Adjustable current limit protects motor against overcurrent and it can also be used as an end-stop. This device has also two settable speeds, which are usefull in positioning applications. Control inputs FW and BW start the forward and backward run. STOP is for the motor shut-down. In -PLI version there are also PULSE COUNTER which can be used for end limit use. This counter value keep in memory of card also when power is turned off. FAULT output terminal indicates different failure situations. This pin is normally low, but is pulled up in overheat and conditionally also in current trip situation. DISABLE input disables driver as long as this is pulled up externally. Also it is possible to link fault and disable pins of several units together and achieve a syncronous stop. The BRAKE output can be used to
release external magnetic brake or control brake resistor in overvoltage situation.
There are two selectable control modes, continuous and impulse. In continuous mode the motor runs as long as the control is active. In impulse mode a short comand starts the motor, and only a new impulse will change the status. There is also few special settings start-kick and auto reverse. The card has selectable input logics. Inputs are divided in two groups, control and limit -inputs. Groups can be individually set for NPN or PNP logic. The parameters are set with EM-236 interface unit. Operation of the controller and some of its functional values can also be monitored with EM-236 interface unit.
This device is designed to control also with Rs-485 Bus.The control bus use Modbus RTU protocol and with the Bus there can be set, speed, direction, accelaration and deceleration ramps and current limit. Also the monitoring and parameter setting are possible with the Bus. There is a separate instruction for operating the bus.


TECHNICAL DATA

Supply voltage (continuous, max.)10-35V
Overvoltage limit (adjustable)15-40V (hardware limitations)
Start-up voltage9V
Shutdown voltage8V
Motor current (continuous, max.)15A
Motor current (peak, max.)30A
Current limit (adjustable)0.1-20A (Max. 30A at start)
Overheat limit100°C
Start/stop ramp (adjustable)0-5s
PWM frequency2kHz
Speed input scale (Speed-2)0-5V = 0-100% PWM
Input control logicHigh = 4-30V, Low = 0-1V
Control input impedanceTyp. 47kΩ
Pulse input impedanceTyp. 10kΩ
Pulse input frequency (max.)400Hz
Control input response timeTyp. 5ms
Fault output (PNP open collector)12-22V / Max. 50mA
Fault/Disable input activationUin > 4V (PNP)
Brake output (NPN open collector)Max. 35V / 1.5A
Motor and supply connectors2.5mm²
Control connectors1mm²
Dimensions42 x 72 x 25mm
Dimensions (DIN-rail base)45 x 80 x 45mm
CE-tested for industrial environment (EMC)Yes
Operating temperature (Ta)-40...60°C
Weight75g

Product files

EN_em-348-PLI.pdf (1.239,65 KB)
Modbus_common_part_10.2.2021.pdf (393,18 KB)
Modbus_PLI_12.6.2019.pdf (183,03 KB)
EN_em-Rail_bases.pdf (2.833,53 KB)
Stock: 96 pcs.
59,00 €
VAT 0%

AAA - credit rating

ISO-certified suppliers and subcontractors

100% Finnish production chain

Device design, programming, and laboratory testing

Short delivery time

Back to top
Our website uses cookies to enhance user experience. You can adjust your preferences from the settings
1 Items in cart
Cart
Overall:
0,00€