EM-356B-SBL BRUSHLESS DC-MOTOR DRIVER 12-24V 15/20A POSITIONING and MODBUS
EM-356B-SBL is brushless DC-motor driver with hall sensor feedback. The unit has a mosfet power stage with good efficiency and it meets also todays EMC requirements. The driver can be used with 120° commutation. This driver has true 4Q power stage, and it makes possible to use regenerative braking . In this braking method the supply voltage rises, this voltage rising can be controlled with braking
resistor. If uses battery supply then the braking energy can be leaded back to battery and braking resistor will not needed.
The unit has the basic digital command inputs like reset/homing, disable, local/bus and safety stop. There is analog input for position set. EM-356B-SBL has PNP output for fault indication use. Some input and output ports and functions can be set and change with parameters. Alternatively this driver can be also controlled via Rs-485 control bus with Modbus protocol.
Driver includes overvoltage, undervoltage and overtemperature protections. These fault situations are indicated with fault on-board LED.
Current limit situations can be reset with reset input, reset-timer or by setting analog speed control to value to 0.
This -SBL version of EM-356 uses motor feedback pulses also for positioning, little like in servo system. The positioning resolution depends on the numbers of motor poles. for example 1-pole-pari motor 6-positon in round and 7-pole-pair motor 42 position in round.
and this round means motor shaft rounds, so with gearbox the resolution can be improved. Driver has own positioning amplifier and with this can be easily adjusted dynamic and accuracy of system. Driver has also RS-485 bus with Modbus control protcol, this make flexible use and control many driver in system.
Setting can be done digitally with EM-236 interface unit or with Emen-Tool lite program installed in PC and EM-328 adapter cable.
Parameters stored into nonvolatile memory of device. This interface unit can also be monitored the current and rpm of motor. Parameter stting and monitoring can be also done via Rs-485 bus.
Device can be installed in DIN-rail base and some enclosure options are also available.
TECHNICAL DATA
Supply voltage 12-24V ( 11-35Vdc )
Overvoltage shut down 40V
Idle current typ. 30mA
Max current 15A cont. ( Tamb. 40 °C )
Max. current 20A cont. ( with fan, Tamb. 40 °C )
Max current peak 40A ( max 2s )
Max brake output current 10A
Pwm frequency typ. 16kHz
Overtemperature Temp shut down 90°C
Current limit setting 1-40A ( step 1A )
Current limit analog scale 0-5V = 0-40A
Logic level of digital inputs
"off" = 0-1V or open / "on"= 4-30V
Input impedance of logic inputs 10k
Response time of digital input 2ms
Analog input range 0-5V up to 0-10V
Analog input resolution 10bit. ( 1024 step )
Position counter resolution 31b ( 2147 milj. steps )
Input impedance of analog inputs 100k
Input filter of analog input 100Hz
Fault outputs NPN max 50mA
Fan output NPN max. 100mA
EMC measured for industrial and env.
PCB material flammability class UL94V-0
Dimensions 89x73x32mm ( height 44mm with fan )
Weight 150g and 200g with fan
Tiedostot
- EN_em-356B_SBL.pdf - Lataa tiedosto (1388 kt)
- EN_em-352_367SBL_Modbus_Data_Address_rev3.pdf - Lataa tiedosto (138 kt)
- Test_Modbus_connection_with_Qmodbus.pdf - Lataa tiedosto (209 kt)
- EN_em-Rail_bases.pdf - Lataa tiedosto (2834 kt)
Varastotilanne
- 9 kpl varastossa
Hinta
-
92,00 € /kpl