Brushless DC motor controllers
Product files
Items under this category
EM-106A BRUSHLESS DC-MOTOR CONTROL UNIT 12-24V 7A
- Three phase output
- Direction change
- Hall-transducer supply and input
- Supports 60° and 120° commuting
- Adjustable current limit
- Direct or freq.locked driving
- High efficiency
- Inbuilt fuse
- Rail mounting base available
- Compatible with EM-106
- Improved current limit behavior
EM-151B BRUSHLESS DC MOTOR DRIVER 12-24V 25A
- Three phase output
- Open or Closed loop speed cont.
- Controlled direction change
- Dynamic or Regenerative braking
- 60° or 120° commutation
- ±10V control option
- Fault output
- High efficiency
- Thermal protection
- Rail base mountable
EM-206 BRUSHLESS MOTOR CONTROLLER 12-36V 10A
- Three phase output
- Continuous speed adjustment
- Reversing
- Braking
- ±10V control option
- Hall sensor supply and input
- 60º or 120º commutation
- Settable / controllable current limit
- Fault output
- Open or closed loop activity
- High efficiency
- Rail base mountable
EM-206-48 BRUSHLESS MOTOR CONTROLLER 20-56V 5A
- Three phase output
- Continuous speed adjustment
- Reversing
- Braking
- ±10V control option
- Hall sensor supply and input
- 60º or 120º commutation
- Settable / controllable current limit
- Fault output
- Open or closed loop activity
- High efficiency
- Rail base mountable
EM-269A BRUSHLESS DC-MOTOR DRIVER 12-35V 2A
- Only for motors with hall sensor
- Three phase output
- Speed adjustment
- Current limit and trip.
- Open/closed loop modes
- Settable Indication output
- Good efficiency
- Low EMC emissions
- DIN-rail mountable
EM-291A BRUSHLESS DC-MOTOR DRIVER 12-35V 4A
- Only for motors with hall sensors
- Three phase output
- Speed adjustment
- Current limit and trip
- Open/closed loop modes
- Settable indication output
- Good efficiency
- Low current version available ( -LC )
- Low EMC emissions
- DIN-rail mountable
EM-316A Brushless DC-Motor Driver 12-35V 10A
- ONLY to the motors with hall sensors
- Three phase output
- Speed and torgue adjustment
- Open/closed loop modes
- Dynamic braking
- Current limit and trip
- Fault and overcurrent outputs
- 60° / 120° commutation options
- Good efficiency
- Low EMC emissions
- DIN-rail mountable
- EM-316A is compatible with EM-316
- Added EM-A1 card slot for ±10V control
- Rpm-pulse output option ( prog v1.5 )
EM-346 BRUSHLESS DC-MOTOR DRIVER 12-35V 10A
- ONLY to the motors with hall sensors
- Three phase output
- Speed and torque adjustment
- Open/closed loop modes
- Regenerative braking option
- True 4Q-power stage
- Braking resistor output
- Current limit and trip
- Symmetrical control option ±5V or ±10V
- Fault and overcurrent outputs
- Good efficiency
- Low EMC emissions
- DIN-rail mountable
- Rpm-pulse output option
- New in firmware version v1.4
- + improved closed loop features ( param. 1)
- + new operating mode options ( param. 11)
- + one option added disable input ( param. 14 )
- + control for magnetic brake ( param. 18 )
EM-346-48V BRUSHLESS DC-MOTOR DRIVER 24-48V 10A
- ONLY to the motors with hall sensors
- Three phase output
- Speed and torque adjustment
- Open/closed loop modes
- Regenerative braking option
- True 4Q-power stage
- Braking resistor output
- Current limit and trip
- Symmetrical control option ±5V or ±10V
- Fault and overcurrent outputs
- Good efficiency
- Low EMC emissions
- DIN-rail mountable
- Rpm-pulse output option
- New in firmware version v1.4
- + improved closed loop features ( param. 1)
- + new operating mode options ( param. 11)
- + one option added disable input ( param. 14 )
- + control for magnetic brake ( param. 18 )
EM-347A BRUSHLESS DC-MOTOR DRIVER 12-36V 55A EM-347A-fan 12-36V 70A
- ONLY to the motors with hall sensors
- Three phase output
- Speed and torgue adjustment
- Open/closed loop modes
- Dynamic braking
- Control output for cooling fan.
- True 4Q-power stage
- Braking resistor output
- Selectable brake mode
- Current limit and trip
- Symmetrical control option ±5V or ±10V
- Fault and overcurrent outputs
- Good efficiency
- Low EMC emissions
- DIN-rail mountable
- Rpm-pulse output option
- A-version has 20% improved output current
- A-version available with integrated fan
- Firmware v1.4 extended control opt. par. 11
- Firmware v1.9 options added to par. 14 and 17
EM-347B BRUSHLESS with MODBUS( BLDC ) MOTOR DRIVER 12-48V 50A
- Only to the motors with HALL sensors
- motors 12V recom. up to 800W
- motors 24V recom. up to 1200W
- motors 48V recom. up to 1600W
- Three phase output
- Speed and torgue adjustment
- Open/closed loop modes
- Dynamic braking
- Control output for cooling fan.
- True 4Q-power stage
- Braking resistor output
- Selectable brake mode
- Current limit and trip
- Symmetrical control option ±5V or ±10V
- Fault and overcurrent outputs
- Good efficiency
- Low EMC emissions
- DIN-rail mountable
- Rpm-pulse output option
- B-board has extended voltage range
- B-board has shutdown input for idle reduction
- B-board replaced earlier A-versions ( all voltage )
- B-board has Rs-485 port ( Modbus RTU )
- B-board support B version firmwares
- B-version HW and SW offer special stop modes
- B-version board v3 support hold current option
- Prog. v1.8 param. 21 added "hold current"
- Prog v1.9 Im zero calib. added, param. 1 =3
- Prog v1.9 magn brake "slow" added to param. 1
EM-352 BRUSHLESS DC-MOTOR DRIVER 12-35V 8A
- Only for motor with Hall sensors
- Speed and torgue adjustment
- Open/closed loop modes
- Regenerative braking option
- Braking resistor output
- Fan control output
- For motors up to 80W@12V 125W@24V
- Current limit and trip
- Indication output option
- Good efficiency
- Low EMC emissions
- DIN-rail mountable
- Firmvare v1.0 or later
- Rs-485 Modbus control option
- Firmware v1.7 or later
- Added input functions, par. 11,13, 20
- Added power on mode, parameter 15
EM-352-SBL BRUSHLESS DC-MOTOR DRIVER 12-24V 8A POSITIONING and MODBUS
- Three phase output
- Speed and torgue adjustment
- Rs-485 Modbus cont. option
- Servo amplifier for positioning
- Regenerative braking option
- Position counter 31bit
- True 4Q-power stage
- Braking resistor output
- Output current 8A
- Current limit and trip
- Good efficiency
- Low EMC emissions
- Compact size
- DIN-rail mountable
- Firmware v1.6 added features
- current limitation smoothed
- counter max . freq. increased
- start level added, param. 19
- Fiemware v1.9 added par. 18 pos. 8
EM-356B BRUSHLESS DC-MOTOR DRIVER 12-35V 15A ( 20A )
- Only for motors with Hall sensors
- Speed and torgue adjustment
- Open/closed loop modes
- Regenerative braking option
- Braking resistor output
- Fan control output
- For motors up to 100W @ 12V,
- and 200W@ 24V
- Current limit and trip
- Indication output option
- Good efficiency
- Low EMC emissions
- DIN-rail mountable
- Firmvare v1.0 or later
- Rs-485 Modbus control option
- Firmware v1.7 or later
- Added input functions, par. 11,13, 20
- Added power on mode, parameter 15
EM-356B-SBL BRUSHLESS DC-MOTOR DRIVER 12-24V 15/20A POSITIONING and MODBUS
- ONLY to the motors with hall sensors
- Three phase output
- Speed and torgue adjustment
- Rs-485 Modbus cont. option
- Servo amplifier for positioning
- Regenerative braking option
- Position counter 31bit
- True 4Q-power stage
- Braking resistor output
- Fan control output
- Output current 25A with fan
- Current limit and trip
- Good efficiency
- Low EMC emissions
- DIN-rail mountable
- EM-356B-SBL replaces earlier EM-356A-SBL
- EM-356B works -B version or later firmwares
- v1.8 improved position counter freq.
- v1.8 improved currrent limit features
- v1.8 added param. 19 "start level"
EM-366 BRUSHLESS DC-MOTOR DRIVER 12-48V 30/25A
- Only for motors with Hall sensors
- Speed and torgue adjustment
- Open/closed loop modes
- Regenerative braking option
- Braking resistor output
- Fan control output
- For motors up to 200W @12V
- 300W @ 24V and 400W @ 48V
- Current limit and trip
- Indication output option
- Good efficiency
- Low EMC emissions
- DIN-rail mountable
- Firmvare v1.0 or later
- Rs-485 Modbus control option
- Firmware v1.7 or later
- Added input functions, par. 11,13, 20
- Added power on mode, parameter 15
EM-366-SBL BRUSHLESS DC-MOTOR DRIVER 12-48V 30/25A POSITIONING and MODBUS
- ONLY to the motors with hall sensors
- Three phase output
- Speed and torgue adjustment
- Analog or Rs-485 Modbus control
- Servo amplifier for positioning
- Regenerative braking option
- Position counter 31bit
- True 4Q-power stage
- Braking resistor output
- Fan control output
- Output current up to 30A
- Current limit and trip
- Good efficiency
- Low EMC emissions
- DIN-rail mountable
- Firmware v1.6 added features
- current limitation smoothed
- counter max . freq. increased
- start level added, param. 19